Use the workshop’s ICOM Next A for remote BMW programming

With eLinehub, you can connect ISTA on your diagnostic PC to the workshop’s ICOM Next A and use your own BMW access for remote programming.

How eLinehub connects ICOM Next A to your diagnostic PC

Tap an image to enlarge it.

In ISTA Connection Manager, you can select the workshop’s ICOM as if it were on your local network.

When a BMW repair calls for ISTA programming

Use the BMW procedure for the VIN to decide whether to program the vehicle. Two jobs illustrate how the software level or the replacement hardware can change that decision.

The center display goes black and the head unit restarts.
For an HU-H3 with B7F8F9, check which bulletin applies. One calls for checking the vehicle’s I-level before programming. Another traces the same symptom to the My BMW App version. BMW SIB 65 01 24 · BMW SIB 65 12 24
ISTA cannot program a replacement telematics module.
Compare the original and replacement TCB4 variants. For a WAVE-11 High to WAVE-01 High replacement on a covered BMW, select the conversion specified in ISTA before programming the vehicle. BMW SIB 84 05 25

For a diagnostic session using the workshop’s wired ENET cable, see BMW remote diagnostics over ENET.

Connect the workshop’s ICOM Next A to ISTA

Tap an image to enlarge it.

Mechanic — connect the ICOM and share the order

  1. Connect the interface. Connect ICOM Next A by Ethernet to the workshop PC running eLinehub Mechanic. Switch on the ignition, then plug the ICOM into the vehicle’s diagnostic port. BMW connection guide

  2. Share the ICOM connection. Create an order for BMW ICOM Next A, choose Your Designated Expert, then share the Ethernet adapter connected to the ICOM.

  3. Send the Passcode. Give the Technician the six-digit Order Passcode. For a programming job, connect a BMW-approved external power supply and stay with the vehicle.

Send the six-digit Order Passcode to your Technician.

Technician — identify the BMW and review the measures plan

  1. Claim the order. In eLinehub Technician, click Claim Order. In the dialog, enter the six-digit Order Passcode and click Confirm.

    Click Claim Order above the empty order list to enter the Passcode.
  2. Bridge the ICOM connection. When the order shows Ready, select the workshop adapter connected to the ICOM under Mechanic Network Adapter. For the setup shown here, select eLinehub Link on your PC and connect in Relay mode.

    Select the Ethernet adapter connected to ICOM Next A. Choose eLinehub Link as the target.
  3. Verify the ICOM and VIN. In ISTA, open Read out vehicle data. In Connection Manager, find the workshop’s ICOM by its identifier. Check the VIN shown for that interface against the vehicle before connecting. If the interface is missing, check ICOM power and Ethernet at the car first, then the selected adapter and Relay connection. If the VIN is missing or differs, check the ignition and confirm the vehicle with the Mechanic before proceeding.

    Once the bridge is established, open ISTA and confirm that it recognizes the ICOM and the vehicle.

Before programming, confirm external power with the Mechanic and review all control units in the ISTA measures plan. Follow the BMW procedure through its final function check. Mechanic guide · Technician guide

BMW diagnostic interfaces supported by eLinehub

This workflow uses ICOM Next A over Ethernet. For programming, use the interface specified for the vehicle and the job. BMW AOS interface guidance

  • ENET Cable
  • BMW ICOM Next A
  • TabScan T6BMW
  • TabScan T6BBA
  • VNCI J2534 Nano
  • TOPDON RLink X7
  • BMW ICOM A
  • TOPDON RLink X3
  • TabScan T6J2534
  • TOPDON RLink J2534
  • TOPDON RLink Lite
  • OEM VCI
  • Other VCI
  • Bosch Mastertech II VCI (MTS 6531)
  • CarDAQ-Plus 3

Network recommendation

  • Use wired internet on both PCs where possible for a stable remote connection.

Start a BMW programming session with ICOM Next A

For you, the Technician: Have ISTA and the BMW access required for the job ready on your Windows PC.

For the workshop: Have the ICOM, a Windows PC and the external power supply at the car.

Use the Web App to manage the order and the Windows Client to connect to the ICOM.

Technician

Claim the order from your diagnostic PC, then open ISTA to identify the vehicle.

Manage orders in the Technician Web AppDownload the Technician Windows Client

Mechanic

Create the order and share the Ethernet port connected to ICOM Next A.

Open Mechanic Web AppDownload Mechanic Client